Rattery Sawmill SW Ltd manufacture a wide range of timber Entrance and Driveway Gates in a variety of styles and sizes to suit any entrance.
All our gates are manufactured from Douglas Fir, which is grown locally in the South West or Wales. Douglas Fir is a very suitable wood for gates as it is subject to low shrinkage and has good stability. It is strong and elastic. The wood is also resistant against fungal and insect infestation and exhibits good natural durability when exposed to the elements.
We also treat all the wood used for making gates with Wolmanit CX-8F wood preservative, which is triple treated in our own on-site pressure treatment plant.
This design has a straight top rail and between the frame we fit 3/4 inch (19mm) tongue-and-groove panelling (TGV). This gate is constructed using mortice and tenons, with the tenons being held in place with hardwood pegs.
The thickness of our gates are normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has a top rail with a single (convex) curve on the top part of the rail and the bottom part is horizontal. This gate is constructed using mortice and tenons, with the tenons being held in place with hard wood pegs. These gates are often ordered as a single gate.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has a single curve top rail and between the frame we fit ÿ? inch (19mm) tongue-and-groove panelling (TGV).
The top rails are a single curve with the higher part in the middle of each half of the gate (Convex). This gate is constructed using mortice and tenons, with the tenons being held in place with hard wood pegs.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has a rail that increases in height on the top part of the rail from the hinge side of the gate into the middle of the gate. The bottom of the rail stays horizontal. This gate is constructed using mortice and tenons, with the tenons being held in place with hard wood pegs.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has a single curve top rail and between the frame we fit 3/4 inch (19mm) tongue-and-groove panelling (TGV). The top rails are a single curve with the height increasing from the hinge side to the middle of the gate. This gate is constructed using mortice and tenons, with the tenons being held in place with hard wood pegs.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has a double curve top rail and between the frame we fit 3/4 inch (19mm) tongue-and-groove panelling (TGV). The top rails are a double curve with the height increases from the hinge side to the middle of the gate. This gate is constructed using mortice and tenons, with the tenons being held in place with hard wood pegs.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has pales in the upper part of the gate with tongue-and-groove panelling below. The top rail is horizontal (straight). Under the pales is a horizontal straight rail that sits above the tongue-and-groove panelling (TGV), which is 3/4 inch (19mm) thick.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has pales in the upper part of the gate with tongue-and-groove panelling below. The top rails are a single curve which decrease in height from the hinge side to the middle of the gate (Concave). Under the pales is a horizontal straight rail the sits above the tongue-and-groove panelling (TGV), which is 3/4 inch (19mm) thick.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has pales in the upper part of the gate with tongue-and-groove panelling below. The top rails are a double curve (like a stretched S shape) with the height increasing from the hinge side to the middle of the gate. Under the pales is a horizontal straight rail the sits above the tongue-and-groove panelling (TGV), which is 3/4 inch (19mm) thick.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.
This design has pales in the upper part of the gate with tongue-and-groove panelling below. The top rail is horizontal apart from a middle section which is a downwards concave curve. Under the pales is a horizontal straight rail that sits above the tongue-and-groove panelling (TGV), which is 3/4 inch (19mm) thick.
The thickness of our gates is normally either 2 5/8 inches (67mm) or 3 inches (76mm) to accommodate single strap or double strap hinges respectively.
Please get in contact to discuss the width and height of the gate you require. We would be happy to give you a quote.